Use port mirroring on a WR switch (WRS)

1. Introduction

Although port mirroring is supported by WRSs a corresponding command option is not documented in the user manual.

Generally, port mirroring is used on a network switch to send a copy of network packets seen on one switch port to another switch port for monitoring of network traffic. It helps network engineers or administrators to analyse and debug data or diagnose errors.

2. Port mirroring in WRS

A WRS firmware provides an CLI tool, rtu_stat, which features options for port mirroring. It can mirror the inbound and outbound traffic separately only on a single port.

The capabilities of port mirroring options regarding source/destinataion ports and traffic type are listed in Table 1 below. Note: these capabilities have been tested in an access-layer, VLAN-aware WRS (v6.0.1), which is configured according to the GSI Timing Network v2 (TN2) setup.

Table 1. Port mirroring capabilities by rtu_stat

Ports (src -> dst) Traffic Applicable
single src/dst (wri3 -> wri13) inbound yes
single src/dst (wri9 -> wri13) outbound yes
single src/dst (wri3 -> wri13 AND wri3 -> wri13) in & out yes
2 sources, single dst (wri9 -> wri13 AND wri3 -> wri13) in & out yes
single src, multi dst (wri3 -> wri13 AND wri3 -> wri14) in, out, both no
multi src, multi dst (wri3 -> wri13 AND wri4 -> wri14) in, out, both no
The usage syntax can be get by invoking rtu_stat -h:

   list:              List the routing table including
                      port mirroring settings (same as empty command)
   mirror ingress <src_port> <dst_port>: Enable mirroring of ingress traffic
                                         from src_port to dst_port
   mirror egress  <src_port> <dst_port>: Enable mirroring of egress traffic
                                         from src_port to dst_port
   mirror off:      Turn off port mirroring
...
where:
   <port>          port number on which RTU rule is registered; it is a port
                   number from 1 to 18, or the CPU (19)

3. Examples

3.1. Mirroring inbound traffic only

Enable mirroring inbound traffic on wri3 to wri13:
rtu_stat mirror ingress 3 13

The command takes effect immediatelly showing the final status like:
...
RTU Port Mirroring Config Dump:
 Status:  Enabled
 Ingress: port 3 -> port 13

3.2. Mirroring inbound and outbound traffic (same source port)

Enable mirroring both inbound and outbound traffic on wri3 to wri13:
rtu_stat mirror ingress 3 13
rtu_stat mirror egress 3 13

In this case the final status should be:
...
RTU Port Mirroring Config Dump:
 Status:  Enabled
 Ingress: port 3 -> port 13 
 Egress:  port 3 -> port 13

3.3. Mirroring inbound and outbound traffic (different source ports)

Enable mirroring inbound traffic on wri3 to wri13 and outbound traffic on wri9 to wri13:
rtu_stat mirror ingress 3 13
rtu_stat mirror egress 9 13

The result should look like:
...
RTU Port Mirroring Config Dump:
 Status:  Enabled
 Ingress: port 3 -> port 13 
 Egress:  port 9 -> port 13

-- EnkhboldOchirsuren - 15 Sep 2021
Topic revision: r3 - 24 Mar 2022, EnkhboldOchirsuren
This site is powered by FoswikiCopyright © by the contributing authors. All material on this collaboration platform is the property of the contributing authors.
Ideas, requests, problems regarding Foswiki? Send feedback